Quick Ship Products
In stock models ship in 48 hours or less, 5-day shipment if accessories are required.
Panel Fans
In stock models ship in 48 hrs or less
Standard Panel Fan (Direct Drive) - Series 02SH
- In stock models ship in 48 hours or less.
- 5-day shipment if accessories are required.
- Exclusive Air-Seal Ring design
- Totally enclosed fan cooled motor
- Adjustable pitch propeller on 24" to 36" fans
- One-piece aluminum, airfoil type-2 bladed propeller on 40" to 48" fans
Utility Fans
In stock models ship in 48 hrs or less
Utility Fans - Series 22F
- In stock models ship in 48 hours or less.
- Compact design; versatile; durable construction
- Requires limited space
- Totally enclosed, fan cooled motor
- Tilt-head type can be adjusted up or down.
- Series 22F has drilled flat base for wall, column, or ceiling mount.
Cooling Fans
In stock models ship in 48 hrs or less
Cooling Fans - Series HKA
- In stock models and in stock accessories ship in 48 hours or less.
- Polyethylene venturi orifice ring
- Efficient cast aluminum, airfoil propeller
- Front and rear, OSHA compliant integral guarding
- Durable, high quality finish
- Quiet operation
- Motor is totally enclosed all over, 115/230/60/1 voltage with 6' cord and plug
- Colors: 18' and 24" available in black; 32" and 36" available in yellow
Roof Vents
In stock models ship in 48 hrs or less
Upblast Roof Vent (Direct Drive)
- In stock models ship in 48 hours or less.
- 5-day shipment if accessories are required.
- Powder-coated galvannealed steel windband and panel; Galvanized damper lids
- Totally enclosed, fan cooled motor
- Adjustable and fixed pitch propeller on 24" to 36" fans; one-piece cast aluminum airfoil type-2 bladed propellers on 40" to 48" fans
- Pre-fab roof curb available; Galvanized construction; 8" high for flat roof
In stock models ship in 5 days or less
Upblast Roof Vent (Belt Drive)
- In stock models ship in 5 days or less.
- Exterior motor mounting arrangement places the motor and belts out of airstream, making the unit ideal for handling tempered air, smoke, dust and fumes.
- Fan is heavy gauge, painted hot rolled steel, bolted to powder-coated galvannealed panel. Stack cap and windband are painted galvvannealed steel. Has galvanized damper lids.
- Cast aluminum, 6-blade, Type W, airfoil propeller
- Motors are totally enclosed and fan cooled. All motors are 1750 RPM.
- Lube tubes are standard with compatible relubricable motor.
- Weather cover, stack cap, and curb panel are standard.
- Units are shipped, assembled, and skid mounted.
- Pre-fab roof curb available; Galvanized construction; 8" high for flat roof
Duct Fans
In stock models ship in 5 days or less
Duct Fan (Belt Drive)
- In stock models ship in 5 days or less.
- 6-blade "W" prop operates efficiently under pressure with low RPM and brake horsepower
- Bearings are heavy-duty, pillow block, boll or roller type selected for minimum L-50 life of 500,000 hrs for horizontal fans; 300,000 hrs for vertical fans, and include extended lubrication fittings.
- Shaft seal and slinger are standard.
- Motors are totally enclosed, fan cooled, and out of the airstream.
In stock models ship in 5 days or less
Duct Axial® Fan (Belt Drive)
- In stock models ship in 5 days or less.
- One-piece, cast aluminum, 6-bladed, airfoil-type propeller provides maximum efficiency at medium static pressure ranges, with low speed and low noise characteristics.
- Bearings are heavy-duty, pillow block, boll or roller type selected for minimum L-50 life of 400,000 hrs for horizontal fans; 250,000 hrs for vertical fans, and include extended lubrication fittings.
- Shaft seal and slinger are standard.
Vane Axial Blowers
In stock models ship in 5 days or less
Vane Axial Blower (Belt Drive), Type VA
- In stock models ship in 5 days or less.
- Impellers are 7-bladed, airfoil design of cast aluminum construction. Large hub-to-blade ratio prevents back flow of air. Moves large volumes of air at high static pressures.
- Bearings are heavy-duty, ball or roller type selected for minimum L-50 life of 200,000 hrs and include extended lubrication fittings.
- Housings are one-piece, heavy gauge, hot rolled steel with internal discharge vanes welded in the blower housing.
- Extended lube tubes with compatible relubricable motor.
- Stocked as "G" (General Industrial) Duty construction.
Centrifugal Fans
In stock models ship in 5 days or less
Backward Curved Centrifugal Fans Packaged (Belt Drive)
- In stock models ship in 5 days or less with accessories.
- Clockwise rotation (CCW not available from stock) with top horizontal discharge standard. Can rotate in field. Stock fans cannot be rotated to BAD, TAD, and DB. (Flanges interfere with base.)
- Class II construction. Housing of heavy gauge , hot rolled steel.
- Wheels are non-overloading backward curved, with single thickness airfoil blades.
- Fans are stocked with shafts and bearings to accommodate maximum performance.
- Weather cover, drilled inlet and outlet flanges (1-1/2" wide), and ceramic shaft seal
- Maximum temperature is 250°F.
In stock models ship in 5 days or less
Fiberglass Backward Curved Centrifugal Fan, Packaged (Belt Drive)
- In stock models ship in 5 days or less with motors and drives mounted.
- Clockwise rotation (CCW not available from stock) with top horizontal discharge standard. Can rotate in field. Stock fans cannot be rotated to BAD, TAD, and DB. (Flanges interfere with base.)
- Class II construction.
- Offers non-overloading efficiency and economy in corrosive atmospheres up to 10" W.G.; temperatures to 250°F.
- Wheel is one-piece airfoil type, constructed with vinylester resin.
- Housing constructed of special corrosive resistant polyester resin *plus flame retardant additives, reducing the flame spread rate below 25.
- Base is hot rolled steel, epoxy coated.
- Internal hardware is 304 stainless steel encapsulated with fiberglass.
- The shaft is 304 stainless steel.
- Flanged outlet and inlet, and epoxy coated weather cover are standard.
Fiberglass Fans
In stock models ship in 5 days or less
Fiberglass Belt Drive Duct Fan
- In stock models ship in 5 days or less.
- Excellent in corrosive atmospheres - temperatures up to 200°F.
- Weighs 25% less than comparable carbon steel equipment.
- 6-bladed, fiberglass airfoil-type propeller provides maximum efficiency at medium pressure ranges with low speeds and low noise characteristics
In stock models ship in 5 days or less
Fiberglass Duct Axial Fan
- In stock models ship in 5 days or less.
- Excellent in corrosive atmospheres - temperatures up to 200°F.
- Weighs 25% less than comparable carbon steel equipment.
- 6-bladed, fiberglass airfoil-type propeller provides maximum efficiency at medium pressure ranges with low speeds and low noise characteristics
In stock models ship in 5 days or less
Fiberglass Backward Curved Centrifugal Fan, Packaged (Belt Drive)
- In stock models ship in 5 days or less with motors and drives mounted.
- Clockwise rotation (CCW not available from stock) with top horizontal discharge standard. Can rotate in field. Stock fans cannot be rotated to BAD, TAD, and DB. (Flanges interfere with base.)
- Class II construction.
- Offers non-overloading efficiency and economy in corrosive atmospheres up to 10" W.G.; temperatures to 250°F.
- Wheel is one-piece airfoil type, constructed with vinylester resin.
- Housing constructed of special corrosive resistant polyester resin *plus flame retardant additives, reducing the flame spread rate below 25.
- Base is hot rolled steel, epoxy coated.
- Internal hardware is 304 stainless steel encapsulated with fiberglass.
- The shaft is 304 stainless steel.
- Flanged outlet and inlet, and epoxy coated weather cover are standard.
Heaters
In stock models ship in 48 hrs or less
Vertical Gas Fired Make-Up Air Heater
- In stock models ship in 48 hours or less.
- IRI pipetrain
- 460 volt and natural gas only
- Economical and energy efficient
- Each unit is a complete air supply system in a self-contained package, consisting of a fan, burner, 3-place remote station and controls.
- Excellent for localized supply air applications
- Industrial duty - constructed of powder-coated, 12 gauge, hot rolled steel.
- Unit's props are #319 cast aluminum alloy
- Low noise - all Series 78V units are at 83 dBA or less at 5'
- Units are direct drive, no belts to adjust or replace.
- Extended lube lines to the motors are standard.
- Series 78V vertical units are set up for roof curb mounting.
- Units are ready for connectio to gal line and power source.
- Standard units have bird screen and fliter racks, less filters.
In stock models ship in 48 hrs or less
Door Heaters
- In stock models ship in 48 hours or less.
- IRI/FM gas plumbing train
- 460 volt only
- Electronic flame safeguard with LED status
- Magnetic starter
- Rear inlet guard
- Block and vent valves
- High and low gas pressure switches
- High temperature limit switch
- Remote station for floor mounting with selector switch
- Door switch for automatic start and stop of unit
Marine Duty
In stock models ship in 48 hrs or less
Marine Duty Duct Axial® Fan (Direct Drive)
- In stock models ship in 48 hours or less.
- 5-day shipment with 230V motor voltage
- 6-blade airfoil design, cast aluminum propeller, mounted with taper lock bushing
- Housings are one-piece, heavy gauge, hot rolled steel with steel flanges.
- Standard finish is a marine duty inorganic zinc base coat applied to sand blasted steel housings and an epoxy coating applied to cast aluminum impellers. THis provides excellent weathering characteristics and protection against sea spray.
- Motors are totally enclosed, certified to meet IEEE 45, 50°C ambient rise below deck, 230/460/60/3
- Fractional HP motors equipped with permanently lubricated bearings
- Integral HP motors equipped with relubricable bearings as standard. 12", 3/4 HP fan available in single phase 115 volt.
- Motors are pre-wired 460V with electrical leads extended to watertight conduit boxes located on the exterior of the fan housings. 230V available with modification fee applied.
- Blowers are designed for mounting in any position from horizontal to vertical.
In stock models ship in 48 hrs or less
Adjustable and Fixed Pitch Marine Duty Duct Fan
- In stock models ship in 48 hours or less.
- Propellers are cast aluminum, airfoil design, mounted with taper lock bushing.
- Housings are one-piece, heavy gauge, hot rolled steel with steel flanges.
- Fractional HP motors are equipped with permanently lubricated, non-regreasable bearings.
- Integral HP motors equipped with relubricable bearings as standard.
- Integral HP motors equipped with relubricable bearings as standard. 12", 3/4 HP fan available in single phase 115 volt.
- Motors are pre-wired 460V with electrical leads extended to watertight conduit boxes located on the exterior of the fan housings. 230V available with modification fee applied.
- Blowers are designed for mounting in any position from horizontal to vertical.
Super Duty
Ships in 15 to 20 business days
SD6X: 43,000 CFM
The SD6X fan is built for huge areas that need massive, all-you-got airflow. With a totally-enclosed 2.0 HP Heavy Industry inverter motor and a wall mounted controller to control the power and the speed, she gets the job done, and is built to last a long time in extreme conditions. The variable speed feature allows you to adjust the airflow for different seasons, including winter when you can run it on a slow setting to simply destratify the warmer air from the ceiling and also minimize floor sweating. Needs to hang at least 10’ from the floor, and at least 3’ from the ceiling. The ideal hanging height is about 18 to 30 feet high, which gives a nice breeze over a large floor area.
Ships in 15 to 20 business days
SD6FF: 43,000 CFM
The SD6FF floor fan is built for big air movement on the go and where you need it most. With a totally-enclosed 2.0 HP Heavy Industry inverter motor and mounted variable speed controller, this fan can be moved and positioned to provide cooling airflow anywhere in your facility. Directional and locking castors will assure that it stays there. This bulletproof setup includes OSHA compliant guarding for safety and can handle extreme ambient heat up to 135 degrees F, and because the controller converts the input power to 3 phase 220 voltage it is highly efficient at only 5.8 amps.
Ships in 15 to 20 business days
SD5X: 33,000 CFM
The SD5X fan is perfect for large areas that need huge, even airflow. With a totally-enclosed 1 HP farm duty motor, she gets the job done, and is built to last a long time. While she is big and bad, she is easy to install, efficient, quiet, and powerful. Needs to hang at least 10’ from the floor, and at least 3’ from the ceiling. Those big buildings get warm in the afternoon and this fan moves big air to make it tolerable to get ‘er done each day. If you are lucky enough to have A/C, this fan will allow you to turn up the thermostat and save some money.
Ships in 15 to 20 business days
SD4X: 23,000 CFM
The SD4X fan is perfect for medium areas that need huge, even airflow. With a totally-enclosed 1 HP farm duty motor, it gets the job done, and is built to last a long time. Installation is a breeze, and it is efficient, quiet, and powerful. Needs to hang at least 7’ from the floor, and at least 2’ from the ceiling. Those summer days get dangerously hot and this fan moves big air to make it tolerable to get ‘er done each day. If you are lucky enough to have A/C, this fan will allow you to turn up the thermostat and save some money.
Ships in 15 to 20 business days
SD3X: 13,000 CFM
The SD3X fan is perfect for small to medium size areas that need serious cooling airflow, a light, single speed, and a totally-enclosed farm duty motor. With an OSHA compliant grille, this fan can be hung with only a 7’ clearance from the floor – instead of the 10’ clearance required for unprotected metal blade fans.
Extractors
In stock ships in 20 business days
PR EXC/EXD
These models have the same unique features and design as PR. The differences lays in the grounded structure and that PR EXC/EXD meet the requirements of the ATEX Directive 94/9/EC Category 2 for gases and dust:
• Zones 1 and 21
• EX II 2 GD marking
The PR EX is available in two versions:
• EXC with black chemical resistant PE hose
• EXD with semi-transparent white PU hose for dust-related pollutants
PR for ATEX environments is designed according to Movex’s basic principles. External arm supports natural and direct airflow providing minimal pressure drop and low risk of blockage.
Product is assembled and tested.
In stock ships in 20 business days
PTEX
Telescopic extractor arm for confined work areas
A compact and flexible telescopic extractor arm with low pressure drop. The extractor arm has a diameter of 125 mm and its length can be extended from 1.3 to 2.1 meters. A gas spring balances the weight of the arm, and PTEX is equipped with an adjustment knob at the upper friction joint, which makes adjustment very easy. External support arms produce low pressure drop and little risk of blockage. The smooth interior of the suction tube makes PTEX very easy to clean.
In stock ships in 20 business days
ME
Ideal extractor for laboratory environments.
The unique design of the Movex ME results in a very low pressure drop, which produces many valuable benefits:
- Energy-saving
- Lower noise levels
- Less risk of disruptive ventilation noise
- Low pressure drop without using a larger dimension system
- Easy to combine with other extractors in the same ventilation system
The standard version is suitable for extracting most types of airborne pollutants in :
- Laboratories
- Schools and Universities
- Hospitals
- Pharmaceutical Industry
- Hair Salons
- Electronics Industry
Motors & VFDs
In stock ships in 24-48 hours
F510 Fan & Pump AC Drives
1 HP through 800 HP
Features:
- Control Modes for V/F, Sensorless Vector, Sensorless Vector with Permanent Magnet Motor
- Built-in PLC as Standard
- Operation and Engineering Units Standard
- LCD Keypad with Remote Mounting Capabilities
- PID Control with Advanced Diagnostics and Sleep Mode
- 1 to 150 HP (Variable Torque), 230V, 50/ 60Hz, 3-Phase
- 1 to 800 HP (Variable Torque), 460V, 50/ 60Hz, 3-Phase
- Plenum Rated
- Diagnostics Registers for Troubleshooting
- Flexible Input/ Output Configurations that Incorporate Normally Open or Normally Closed Signals
- 0 to 400 Hz Speed Range
- Built-in Modbus, BACnet, and Metasys (N2) Protocols via (RS485 or RJ45 Interface)
- Enhanced Design for Smoother and Quieter Motor Operation
- Real Time Clock ( Standard on Models with LCD Keypad )
- PTC Input Available for Direct Thermal Protection of the Motor
- Thermal Management on the Heat Sink for Over Temperature Fault Avoidance
- Master-Follower Control Mode Built-in
- EMI Protection that Complies with EM61800-3 with Optional Filter
- EMS Protection that Follows EN61800-3
- UL, cUL, and CE Approved
In stock ships in 24-48 hours
MAX-E1® NEMA Premium Efficiency
Totally Enclosed Fan Cooled, [EP], [E], [E]_C], [EPV_C]
- Horsepower - 3/4 HP through 800 HP
- Speed - 3600, 1800, 1200, 900 RPM
- Voltage - 230/460V (usable on 208V)
- Frequency - 60 Hz.
